HUBUNGAN ANTARA KEAUSAN TEPI PAHAT DENGAN RASIO DELAMINASI LUBANGATAS PADA PROSES MENGGURDI KOMPOSIT BERPENGUAT SERAT DAUN NANAS ( PALFs )

mur dani murdani(1*), Ismet Hari Mulyadi Ismet Hari Mulyadi(2), Ismet Hari Mulyadi Ismet Hari Mulyadi(3)

(1) universitas andalas padang
(2) Universitas andalas
(3) Universitas andalas
(*) Corresponding Author

Abstract


Abstrak

Penelitian ini bertujuan untuk mengetahui hubungan antara terjadinya delaminasi dengan keausan tepi pahat pada proses menggurdi material komposit berpenguat serat daun nanas. Untuk material komposit berpenguat serat daun nanas dipersiapkan dalam bentuk lembaran yang dijalin (woven mat).Lembaran komposit kemudian disusun dalam3 (tiga) lapisan (stacking) dalam matrik termoplastik dengan metoda Hand Lay-up. Adapun orientasi serat masing-masing lembaran adalah 900 dan 450.Komposit kemudian dilubang dengan mempergunakan proses menggurdi dengan dua kondisi, yaitu kondisi ringan dan berat. Kualitas lubang dalam aspek delaminasi dan keausan tepi pahat diukur dengan mempergunakan mikroskop optik yang dilengkapi perangkat lunak pengukuran. Selanjutnya hubungan antara nilai rasio delaminasi dan keausan tepi pahat hasil menggurdi dibangun. Hasil penelitian mengindikasikan bahwa tidak ada hubungan antara pertumbuhan keausan tepi pahat dengan terjadinya delaminasi lubang pada proses menggurdi material komposit ini dan dengan kondisi pemotongan yang dipilih. Hasil ini telah diverifikasi dengan menggunakan Analysis of Variances (ANOVA) dan Trend Analysis.


Keywords


Kata kunci: Komposit berpenguat serat daun nanas, nilai rasio delaminasi, proses menggurdi, keausan tepi pahat.

Article metrics

Abstract views : 75 | views : 9

Full Text:

PDF

References


DAFTARA PUSTAKA

F. Chegdani, S. Mezghani, M. El Mansori, and A. Mkaddem, “Fiber type effect on tribological behavior when cutting natural fiber reinforced plastics,” Wear, vol. 332–333, pp. 772–779, 2015, doi: 10.1016/j.wear.2014.12.039.

C. C. Daniel F. Caulfiel, “Wood Thermoplastic Composites Chapter 13,” 2005.

Barbero E.J. “Introduction to composite materials design, “ Taylor and Francis, New York, 1999, pp 2. .

I. To, Barbero, E.J., Introduction to composite materials design, Third edition. Boca Raton, Taylor & Francis, CRC Press, 2017, pp 3. 2017.

S. V. Joshi, L. T. Drzal, A. K. Mohanty, and S. Arora, “S. V. Joshi, L. T. Drzal, A. K. Mohanty, dan S. Arora, ‘Are natural fiber composites environmentally superior to glass fiber reinforced composites?,’ Compos. Part A Appl. Sci. Manuf., vol. 35, no. 3, hal. 371–376, 2004,” vol. 35, no. 3, pp. 371–376, 2004, doi: 10.1016/j.compositesa.2003.09.016.

A. Ticoalu, T. Aravinthan, and F. Cardona, “A. Ticoalu, T. Aravinthan, dan F. Cardona, ‘A review of current development in natural fiber composites for structural and infrastructure applications,’ South. Reg. Eng. Conf., no. November, hal. 1–5, 2010.],” no. November, pp. 113–117, 2010.

A. Ayensu, “A. Ayensu, ‘Interfacial Debonding of Natural-Fibre,’ Water,” 2000.

D. Verma, P. C. Gope, A. Shandilya, A. Gupta, and M. K. Maheshwari, “Coir fibre reinforcement and application in polymer composites: A review,” J. Mater. Environ. Sci., vol. 4, no. 2, pp. 263–276, 2013.

J. Wong, “Processing of High Performance Thermoplastic Composites What are we learning about this week,” no. March, pp. 1–41, 2017.

A. Lotfi, H. Li, D. V. Dao, and G. Prusty, “Natural fiber–reinforced composites: A review on material, manufacturing, and machinability,” J. Thermoplast. Compos. Mater., 2019, doi: 10.1177/0892705719844546.

O. Faruk, A. K. Bledzki, H. P. Fink, and M. Sain, “Progress report on natural fiber reinforced composites,” Macromol. Mater. Eng., vol. 299, no. 1, pp. 9–26, 2014, doi: 10.1002/mame.201300008.

W. P. Limited, Tsao CC., 2012. Drilling processes for composites, in: Hocheng H (Eds). Machining technology for composite materials: Principles and Practices. Woodhead Publishing Limited, Philadelphia, US. pp 17-60. 2012.

S. O. Ismail, H. N. Dhakal, E. Dimla, J. Beaugrand, and I. Popov, “Effects of drilling parameters and aspect ratios on delamination and surface roughness of lignocellulosic HFRP composite laminates,” J. Appl. Polym. Sci., vol. 133, no. 7, pp. 1–8, 2016, doi: 10.1002/app.42879.

S. Aravindh and K. Umanath, “Delamination in Drilling of Natural Fibre Reinforced Polymer Composites Produced by Compression Moulding,” Appl. Mech. Mater., vol. 766–767, pp. 796–800, 2015, doi: 10.4028/www.scientific.net/amm.766-767.796.

R. Vinayagamoorthy, N. Rajeswari, and S. Karthikeyan, “Investigations of Damages during Drilling of Natural Sandwich Composites,” Appl. Mech. Mater., vol. 766–767, pp. 812–817, 2015, doi: 10.4028/www.scientific.net/amm.766-767.812.

E. Brinksmeier, S. Fangmann, and R. Rentsch, “Drilling of composites and resulting surface integrity,” CIRP Ann. - Manuf. Technol., vol. 60, no. 1, pp. 57–60, 2011, doi: 10.1016/j.cirp.2011.03.077.

P. K. Bajpai and I. Singh, “Drilling behavior of sisal fiber-reinforced polypropylene composite laminates,” J. Reinf. Plast. Compos., vol. 32, no. 20, pp. 1569–1576, 2013, doi: 10.1177/0731684413492866.

M. M. A. Nassar, R. Arunachalam, and K. I. Alzebdeh, “Machinability of natural fiber reinforced composites: a review,” Int. J. Adv. Manuf. Technol., vol. 88, no. 9–12, pp. 2985–3004, 2017, doi: 10.1007/s00170-016-9010-9.

R. Zitoune, V. Krishnaraj, and F. Collombet, “Study of drilling of composite material and aluminium stack,” Compos. Struct., vol. 92, no. 5, pp. 1246–1255, 2010, doi: 10.1016/j.compstruct.2009.10.010.

M. D. Watson and K. B. Wagener, “Ethylene / Vinyl Acetate Copolymers via Acyclic Diene Metathesis Polymerization . Examining the Effect of ‘ Long ’ Precise Ethylene Run Lengths,” pp. 5411–5417, 2000.

D. Kumar, K. K. Singh, R. Zitoune, D. Kumar, K. K. Singh, and R. Zitoune, “Experimental investigation of delamination and surface roughness in the drilling of GFRP composite material with different drills Experimental investigation of delamination and surface roughness in the drilling of GFRP composite material with different dr,” vol. 0340, no. July, 2016, doi: 10.1080/20550340.2016.1187434.

I. Print, I. Online, B. Dwi, and I. Hari, “METAL : Jurnal Sistem Mekanik dan Termal Pengaruh Parameter Pemotongan dan Variasi Susunan Serat Terhadap Terbentuknya Delaminasi pada Proses Menggurdi Material Komposit Serat Nanas,” vol. 01, pp. 1–8, 2018.

I. Kurniawan et al., “PENGARUH PARAMETER MENGGURDI BERTAHAP TERHADAP,” vol. 9, no. 2, pp. 245–254, 2019.

S. A. Songlin and D. John, “An approach to evaluate delamination factor when drilling carbon fiber-reinforced plastics using different drill geometries : experiment and finite element study,” 2017, doi: 10.1007/s00170-017-0880-2.

M. M. Ilham and A. Mufarrih, “Pengaruh Sudut Ujung Pahat terhadap Delaminasi pada Penggurdian Komposit KFRP Effect of Point Angle on Delamination in Drilling of KFRP Composite,” vol. 8, no. 2, 2018.

G. A. Ibrahim, J. Iskandar, A. Hamni, S. Maria, and P. Lestari, “Analisa keausan pahat pada pemesinan bor magnesium AZ31 menggunakan metode taguchi,” vol. 12, no. 1, pp. 29–35, 2017.

M. M. A. Nassar, R. Arunachalam, and K. I. Alzebdeh, “Machinability of natural fiber reinforced composites : a review,” pp. 2985–2986, 2017, doi: 10.1007/s00170-016-9010-9.

S. Jayabal and U. Natarajan, “Drilling analysis of coir-fibre-reinforced polyester composites,” Bull. Mater. Sci., vol. 34, no. 7, pp. 1563–1567, 2011, doi: 10.1007/s12034-011-0359-y.

2022. Interpret all statistics and graphs for Moving Average. Tersedia pada: https://support.minitab.com/en-us/minitab/18/help-and-how-to/modeling-statistics/time-series/how-to/moving-average/interpret-the-results/all-statistics-and-graphs/#mad. Diakses p Minitab 18, “No Title.” .

C. C. Tsao and H. Hocheng, “Taguchi analysis of delamination associated with various drill bits in drilling of composite material,” vol. 44, pp. 1085–1090, 2004, doi: 10.1016/j.ijmachtools.2004.02.019.

H. Hocheng and C. C. Tsao, “Comprehensive analysis of delamination in drilling of composite materials with various drill bits,” vol. 140, pp. 335–339, 2003, doi: 10.1016/S0924-0136(03)00749-0.

A. Velayudham and R. Krishnamurthy, “Effect of point geometry and their influence on thrust and delamination in drilling of polymeric composites,” vol. 185, pp. 204–209, 2007, doi: 10.1016/j.jmatprotec.2006.03.146.




DOI: https://doi.org/10.35314/ip.v12i2.2920

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 INOVTEK POLBENG


This Journal has been listed and indexed in :

         

Creative Commons License
inovtek polbeng by http://ejournal.polbeng.ac.id/index.php/IP is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License